How To Use CO2 When Growing Marijuana
At some point in your marijuana growing career, you will have a desire to incorporate CO2 into your recipe. Chances are, that is why you are reading this article. I have grown marijuana for a long time, and I know first hand that there is a lot of junk information out there on the web in regards to marijuana plants and CO2. Below is some great information that I found on some of our partner sites that I wish I had when I first started growing marijuana:
By Dr. Who
Humans breathe in oxygen (O) and breathe out carbon dioxide (CO2). Plants do the reverse. They "breathe in" CO2 and "breathe out" oxygen (O). This is why plant life is an essential part of the worlds' ecosystem. Without plants, CO2 levels would rise to intolerable levels. Plants use CO2 for growth. It is the essential building block for photosynthesis (along with light and water). Plants cannot grow without CO2. The current levels in the atmosphere are about 350 parts per million (PPM). It is theorized that millions of years ago, levels of CO2 were about 1,500 PPM. Throughout the years, plants have evolved in many ways-and in many ways have stayed the same. Knowing this can be advantageous for us all.
It seems that plants have not lost the ability to use up to 1,500 PPM of CO2. Plant growth can be accelerated by increasing the CO2 levels in your growing area. Conversely, CO2 levels below 250 PPM have a detrimental effect on your plants. If you have six plants growing in your closet, and there is no ventilation, your plants can use the CO2 in a few hours. They then stop growing. You must, at a minimum, provide fresh air for your plants every hour or so. An even better way is to provide supplemental CO2 for your plants by using either a CO2 generator or bottled CO2. Any of these solutions will keep your plants growing at optimal rates. It has been proven that you can increase your growth rates by up to 20 percent and size by up to 30 percent by providing supplemental CO2 at levels over 1,200 PPM. You should never go over 1,500 PPM, as this soon becomes toxic for the plants, and they tend to grow very stringy.
CO2 generators are simply specialized burners that burn either propane or natural gas to produce CO2. A byproduct of this process is water, in the form of humidity. When using a generator, it is a good idea to keep an eye on your humidity levels. CO2 generators are optimized to produce as little heat as possible, while producing as much CO2 as possible. They are normally rated in cubic feet per hour (CFH). A standard 10-foot-by-10-foot-by-8-foot room containing 350 PPM takes about 1 CFH to raise the levels to 1,500 PPM. The level will drop throughout the day, requiring smaller burns to keep the levels constant. A CO2 PPM controller works great for keeping your levels constant with a CO2 generator.
Bottled CO2 can be obtained at most hydroponic or welding stores. You need a regulator/flow meter to get the CO2 out of the bottle in a measured manner. You set the flow rate in CFH and set the regulator on a timer to bring your CO2 levels to the desired level. A few calculations will be needed to set your CO2 levels correctly. You can also use a CO2 PPM controller to maintain your levels.
Plants do not use CO2 at night. It is not necessary to supplement CO2 during your dark cycles (mushrooms are an exception). Properly used, supplemental CO2 will only help your crops if you have all of your other factors in line, such as using a good nutrient mixed at an appropriate strength, changing your nutrients to prevent nutrient deficiencies, having enough (and not too much light) and keeping your temperature and humidity are also plant limiting factors. Once you have dialed in all these, supplemental CO2 can help you gain the most return on your plant growth.
used with permission from Culture Magazine
DR. WHO is a Southern California expert in plant cultivation. Reach him firstname.lastname@example.org.
Here is a GREAT forum post I found at StonerForums.Com by immacannaclubmember:
Carbon Dioxide Enrichment Methods .....
CARBON DIOXIDE (CO2)
Carbon dioxide is an odorless gas and a minor constituent of the air we breathe. It comprises only .03 % (300 parts per million, or PPM) of the atmosphere but is vitally important to all life on this planet!
Plants are made up of about 80-90 % carbon and water with other elements like nitrogen, calcium, magnesium, potassium, phosphorous and trace elements making up only a small percentage. Almost all of the carbon in plants comes from this minor 300 PPM of carbon dioxide in the air.
Plants take in CO through pores, called stomata, in their leaves during daylight hours. They give off oxygen at the same time, the results of a process called photosynthesis. This oxygen that they give off is used by humans and all animal and marine life on this planet. Without it, animal and human life would not be possible.
Oxygen comprises almost 20 % of the earth's atmosphere. Most of it was generated by plant life. The process of photosynthesis combines CO2 and water to form sugars and free oxygen. Simple sugars like C6H12O6 provide plants with energy and are formed into the more complex plant parts such as carbohydrates, amino acids, protein, cellulose, leaves, roots, branches and flowers.
People and animals breathe in oxygen generated by plants and breathe out the CO2 that the plants needÃ³a truly symbiotic relationship. In ancient times, millions of years ago, when there was only plant life on the earth and no animal life, the atmosphere was quite different. There was much more volcanic activity, one of nature's sources of CO2, and the air contained three to four times as much of it than now. Plants thrived. Giant tree ferns reigned supreme and much of our coal, gas and oil deposits were created by them during that long-ago time.
Plants would benefit from more CO2 in the air today, and actually are benefitting as we burn more fuels, one by-product being carbon dioxide. CO2 in the air has increased from 270 PPM to over 300 PPM, more than an 11% increase, in just the last 40 years! This has also worried many scientists because of what is called the greenhouse effect.. The more CO2 there is in the atmosphere, the higher the planet's temperature will go. Too much warming of the planet can melt ice caps, flood coastal cities, spread deserts and famine and drastically change the climate. This effect is somewhat self-regulating however. The oceans absorb a great deal of CO2 giving algae and plankton, 90% of the plant matter on earth, more CO2 to grow on and giving the rest of the plant matter on land more also. This decreases the amount of CO2 in the atmosphere, thereby regulating it. Scientists are just now learning to understand the self-regulating systems that stabilize most factors in our environment.
Biologists and plant physiologists have long recognized the benefits of higher CO2 content in the air for plant growth. Horticulturists and greenhouse growers have used CO generators to enhance growth rates on plants for many years with good results.
With the advent of home greenhouses and indoor growing under artificial lights and the developments in hydroponics in recent years, the need for CO2 generation has drastically increased. Plants growing in a sealed greenhouse or indoor grow room will often deplete the available CO2 and stop growing. The following graph will show what depletion and enrichment does to plant growth:
Below 200 PPM, plants do not have enough CO2 to carry on the photosynthesis process and essentially stop growing. Because 300 PPM is the atmospheric CO content, this amount is chosen as the 100% growth point. You can see from the chart that increased CO can double or more the growth rate on most normal plants. Above 2,000 PPM, CO2 starts to become toxic to plants and above 4,000 PPM it becomes toxic to people.
With the advent of ideal growing conditions conditions provided by metal high-intensity discharge (H.I.D.) lighting systems, hydroponics, environmental controls such as temp., humidity, etc. and complete, balanced plant nutrients such as Ecogrow, the limiting factor on plant growth rate, quality, size and time to maturity becomes the amount of carbon dioxide available to the plants.
There are five common methods of generating extra amounts of CO2:
1. Burning hydrocarbon fuels
2. Compressed, bottled CO2
3. Dry ice
5. Decomposition of organic matter
We will discuss these five methods briefly in turn. In order to make an effective comparison of CO2 generation, benefits and drawbacks, a std. 8' X 8' X 8' or 512 cu. ft. growing area will be used.
1. BURNING HYDROCARBON FUELS:
This has been the most common method of CO2 enrichment for many years. A number of commercial growers and greenhouses use it in their larger structures. The most common fuels are propane, butane, alcohol and natural gas. Any of these fuels that burn with a blue, white or colorless flame will produce carbon dioxide, which is beneficial. If a red, orange or yellow flame is present, carbon monoxide is being generated due to incomplete combustion. Carbon monoxide is deadly to both plants and people in any but the smallest quantities. Fuels containing sulfur or sulfur compounds should not be used, as they produce by-products which are harmful.
Most commercial CO2 generators that burn these fuels are too large for small greenhouse or indoor grow room applications. Some small ones are avai fable or a Coleman lantern, bunsen burner or small gas stove can be used. All of these CO2 generators produce heat as a by-product of CO2 generation, which is rarely needed in a controlled environment grow room but may prove beneficial in winter growing and cool area greenhouses.
The rate of CO2 production is controlled by the rate at which fuel is being burned. In a gas burning CO2 generator using propane, butane or natural gas, one pound of fuel produces approximately 3 pounds of carbon dioxide gas and about 1.5 pounds of water vapor. Approximately 22,000 BTUs of heat is also added. These figures can vary if other fuels are used.
To relate this to our standard example in an 8' X 8' X 8' growing area, if you used ethyl or methyl alcohol in a gas lamp or burner at the rate of 1.3 oz. per day, we would enhance the atmospheric concentration of CO2 to 1300 PPM if the room was completely sealed.
An enrichment standard of 1300 PPM was chosen as it is assumed that 1500 PPM is ideal, and that the plants will deplete the available CO2 supply by 100 PPM per hour. Remember, the normal atmosphere contains 300 PPM of CO2. A 100% air exchange (leakage) every two hours is assumed to be the average air exchange rate in most grow rooms and tight greenhouses. If many cracks and leaks are present, this exchange rate will increase significantly, but added CO2 (above 300 PPM) will also be lost. If a vent fan is in use, disregard CO enrichment, as it will be blown out as fast as it is generated.
A circulation fan is beneficial, as it moves the air about in the greenhouse or grow room. If the air is still, it can cause a "depletion layer effect". This effect causes the CO2 right next to the plant leaf to be quickly depleted. If fresh air carrying additional CO is not brought to this surface, photosynthesis and growth will diminish and eventually cease.
There are a number of factors involved in keeping the CO2 content at the desired concentration level. 1. If the greenhouse or grow room is not tightly sealed up, add up to 50% to the CO2 generator production volume. 2. If temperature is increased fiom 70 F to 90 F, add 20% to the volume generated, and vice-versa. 3. If the grow area contains large or tightly spaced plants, add 20% to 30% to the CO2 volume generated.
If more light is used, more CO2 can be utilized and should be produced proportionately up to the practical limit of 5,000 footcandles per square yard and 1500 PPM CO2 atm. content. When more CO is generated, more water and plant nutrients should be used, again to a practical limit of 2X normal. lf your plants are going to grow faster because of CO2 enrichment, they will need more nutrient and water.
The last factor to consider in maintaining a set CO2 level is the size of your growing area. This is simply done for gas burning and following methods by setting up a mathematical ratio. In our "standard" room (8' X 8' X 8'), we have 512 cubic feet. If your growing area measures 10' X 10' X 20', you have 2,000 cubic feet of volume to contend with. If you want to use the ethyl alcohol/gas-lamp enrichment method, set up the ratio using l.3 oz. by weight of alcohol per day gives:
1.3 oz./day = 512 cu. ft. ------------------ ------------------- X oz./day = 2,000 cu. ft. Then cross multiply: 512 X = 1.3 X 2,000. Dividing both sides by 512 gives you X = (1.3 X 2000)/512, solve for X. X = 5 oz.
You need 5 oz. of ethyl alcohol per day in a 10' X 10' X 20' grow area to generate the same amount (1300 PPM) of CO2 as in a 512 cu. ft. room.
To generate 1500 PPM above the available CO2 (200 PPM) in the same size area, set up the ratio:
1300 PPM = 5 ounces
1500 PPM = X
X = (5 X 1500)/1300 = 5.77 ounces.
NOTE: One pound of CO is equivalent to approximately 8.7 cu. ft. of gas at standard temperature and pressure.
If different hydrocarbon fuels are used, the heat content, in terms of B.T.U. should be taken into account. If the BTU per hour rate is half that of ethyl alcohol, twice as much must be burned to generate the same approximate amount of CO2 desired. The amount of CO2 generated depends on the carbon content of the fuel being used. The BTU per hour heat content can be obtained from literature or suppliers.
2. COMPRESSED, BOTTLED CO2:
This is the second most popular method of CO2 enrichment and provides fairly accurate, controlled results. Compressed CO2 comes in metal containers under high pressure. Small cylinders contain 20 lbs. of compressed CO and large tanks hold 50 lbs. Pressure ranges from 1600 pounds per square inch to 2200 PSI.
To enrich available CO with compressed gas, the following equipment is needed:
1. Tank of compressed CO2
2. Pressure regulator
3. Flow meter
4. Solenoid valve, (plastic or metal)
5. Short-interval 24 hr. timer capable of having an "on time" variable from one to 20 minutes.
6. Connecting tubing, fittings and adapters
PRESSURIZED CO2 ENRICHMENT SYSTEM ARRANGEMENT
This method allows for the injection of a controlled amount of CO2 into the growing area at a given interval of time. The pressure regulator reduces the compressed gas pressure from 2200 lbs./square inch to a more controllable amount (100 to 200 PSI) which the flow meter can handle. The flow meter will deliver so many cubic feet per minute of CO2 to the plants for the duration of time that the solenoid valve is opened. The timer controls the time of day and length of time that the solenoid valve is open.
To operate this CO enrichment system in our standard 8' X 8' X 8' grow room area, we want to add enough CO to increase the near depleted level of 200 PPM to 1500 PPM. We must then add 1300 PPM of CO2 to a volume of 512 cu. ft. We would like to do this in intervals of time relative to the natural air exchange rate (leakage rate) to keep the CO level near the 1500 PPM range.
Let's select an injection time interval (CO2 enrichment time) of every two hours. First, we must determine how many cubic feet of CO2 must be added to 512 cu. ft. of volume to increase our 200 PPM to 1500 PPM. To do this, multiply the room volume of 512 cu. ft. by .0013 (1300 PPM) to obtain 0.66 cu. ft. of CO2 that is needed. Set the regulator at 100 PSI and the flow meter at 20 CFH (Cubic Feet per Hour) or 0.33 cubic feet per minute.
If we set our timer to stay on for two minutes every two hours, we will get the 0.66 cubic feet of additional CO we need to bring the CO level to the 1500 PPM optimum level needed.
Each pound of CO compressed gas contains approximately 8.7 cubic feet of CO gas at atmospheric pressure.
Compressed CO2 costs around 50 cents/lb. at most supply houses. At that rate of 0.66 cu. ft. every two hours for 18 hours per day, this method will cost around 30 cents per day to operate. The timer should be set to deliver CO2 during the "on time" (daylight time) for which the lights are set. This is the only time the plants can use CO2; they do not use it when it's dark.
The compressed gas method of CO enrichment has the advantages of fairly precise control, readily available equipment ($150.00 to $300.00 average cost for an installation) and it does not add extra heat to the growing area. It also works well for small growing spaces and after initial equipment costs, is not expensive to operate.
3. DRY ICE METROD OF CO2 ENRICHMENT:
This method works well for small areas, especially if some cooling effect is desired. Dry ice, solid carbon dioxide, is very coldÃ³about 109 degrees F below zeroÃ³so we suggest you handle it with gloves. Dry ice is available through freezer and meat packing outlets and is relatively inexpensive. In our std. 8' X 8' X 8' room, you would need about 0.8 lbs. of dry ice per day to raise the atmospheric CO2 content to 1300 parts per million. If the growing area is quite warm, 0.8 lbs. can melt much faster than 18 hours. Two methods can be used to regulate this. One is to cut just small pieces, about .1 lb., and add a new piece every two hours to the growing area. The second method is to put the required amount in an insulated styrofoam box with a few small holes cut in it. This will slow the rate of melting considerably but must be "tuned in" to get it just right so 0.8 lbs. melts in the 18 hours of light "on" time. Extra dry ice must be kept in a freezer to prevent loss due to evaporation.
Since CO2 is heavier than air, one good method of distributing it to the plants is to attach the container or dry ice to the light reflectors which are normally placed over the plants. The CO2 will then flow down through or over the lights and evenly bathe the plants. If a circulation fan is used, the dry ice or its container should be placed directly in front or behind it for even distribution. Common to all CO2 enrichment methods, try to seal up the room or greenhouse as best you can, especially around the bottoms of doors and walls.
The dry-ice method will cost around 60 cents per day for our standard sized, 512 cu. ft. grow room. A possible benefit of using dry ice is the cooling effect it produces.
4. FERMENTATION METHOD OF CO2 ENRICHMENT:
Sugar is converted into ethyl alcohol and CO2 when it ferments due to the action of yeast. In this method, the following ingredients and equipment are needed:
1. Suitably sized container, plastic or glass
2. Sugar, common or invert
3. Yeast, brewers or bourgelais wine yeast
4. Yeast nutrient
5. Sealant, cellophane, tape or lid
6. 1/4 plastic tubin
7. 1/4 shutoff valve
9. Starter jar or bottle
A pound of sugar will ferment into approximately half a pound of ethyl alcohol (C2H5OH) and half a pound of CO2. One pound of CO2 makes 8.7 cubic feet of CO2 gas at normal atmospheric conditions. In our standard 8 X 8' X 8' grow room, you will need to generate 512 cu. ft. X .0013 (1300 PPM CO2) = 0.66 cubic feet of CO2 every four hours. It takes time for the yeast to ferment sugar, so the size of container you should use in determined by dividing the cubic feet of growing area (512 Cu. ft.) by 32 = 16 gallons.
A convenient container to use here would be a plastic kitchen garbage can. These are inexpensive and easily obtainable.
To determine how much sugar we need for six weeks of operation or until fermentation ceases, the following calculations are necessary: From the above paragraph, we need 0.66 cu. ft. of CO2 every four hours. If one pound of CO2 makes 8.7 cu. ft. of CO2, we will need 0.08 lbs. of sugar, but because every one pound of sugar only makes 1/2 lb. of CO2, we must double the amount of sugar needed, i.e. 0.08 X 2 = 0.16 lbs. of sugar every four hours. Since there are six four-hour periods in a 24 hour day, the amount of sugar we need is 0.16 x 6 or 0.96 lbs. of sugar per day.
If we round this off to one pound of sugar per day, we will need 42 lbs. of sugar in six weeks. We must consider that only 80 to 90% of the sugar will be completely converted in this length of time, therefore, we should actually use about 48 lbs. of sugar in six weeks.
The sugar solution to start with is 2 1/2 to 3 lbs. per gallon. You can use hot water to start with, as sugar dissolves faster in it than in cold water. You must let it cool to 80-90 degrees F before adding yeast to it or the yeast will be killed. Start with the fermenting container only half-full as you will be adding an extra gallon per week for 6 weeks. Begin with eight gallons per week and 24 lbs. of sugar.
To start the solution fermenting, you will want to make a "starter batch" of sugar water, yeast and yeast nutrient. To do this, use a coke or beer bottle (approx. one pint), dissolve 1/4 lb. of sugar in 10 oz. of warm water (approx. 3/4 full), add a pinch of yeast and two pinches of yeast nutrient to this sugar mixture. Place a balloon on the bottle and set in warm location, 80 to 90 degrees F, for one to two days or until the balloon expands and small bubbles are visible in the solution.
After the starter solution has begun fermenting vigorously, it is added to the main fermentation tank at the same temperature already mentioned. After a day or so, to see that the system is working properly and that CO2 is being generated, close the valve to the supply tube and, if the unit is sealed properly, the balloon should expand in a short period of time. To regulate the amount of CO2 being delivered to the plants, open the valve until the balloon is only half the size of full expansion.
The CO2 supply tube with in-line valve should have a 2" loop in it half full of water to serve as an air-lock. This loop can be held in place with tape on the side of the fermentation tank. The open end of this tube can either be positioned in front of a circulating fan or run through "T" fittings to make additional tubes, the ends of which can be positioned above your plants. Remember, CO2 is heavier than air and it will flow downwards.
Once per week, undo a corner of the Saran Wrap and add an extra gallon of sugar solution and yeast nutrient, then reseal the top with tape. Use three lbs. of sugar and one teaspoon of nutrient per gallon.
After the last gallon is added, after six weeks of operation, let fermentation continue until the balloon goes down and no more bubbles are visible in the "U" tube. When this point has been reached, taste the solution. If is it sweet, fermentation is not complete and a new starter batch should be made and added to the tank. More yeast nutrient should also be used. If the solution is dry (not sweet) like wine, fermentation has stopped and the alcohol content has killed the yeast. At this point, it's time to clean your tank and start a new batch.
The fermentation process is quite good for generating CO2 and relatively inexpensive. Regular or invert (corn) sugar is inexpensive and available. You may have to purchase invert sugar at a wine supply store. This method of generating CO2 will cost approximately 50 to 60 cents per day.
To save money on extra yeast, you can either take out approximately a gallon of fermenting liquid and save for the next batch, or start a second system identical to the first and alternate themÃ³clean and replenish one, then three weeks later, clean and replenish the second.
5. DECOMPOSITION PROCESS OF GENERATING CO2:
When organic matter decomposes due to bacterial action, carbon dioxide is generated. Plants grow lush and vigorously on a tropical jungle floor as a result of this natural decay of dead plant and animal matter. This can increase the available CO2 content from the normal 300 PPM amount to over 1,000 parts per million. This can also be done indoors, for little cost, but is odorous and unsanitary. For these and other reasons, it is not highly recommended. The sterile conditions of a well-set-up hydroponic grow room or greenhouse could be disrupted and adverse bacteria, bugs and disease induced with detrimental effects on your plants.
In conclusion, all these methods will work if done properly and CO2 enrichment is a very beneficial addition to your greenhouse or grow room systems. Some are more practical than others, some less expensive and some require more time and attention. All chemical reactions are temperature dependent and photosynthesis is no exception. With CO2 enrichment, a higher temperature, up to 100 degrees F, can be used, more light may be needed as it is required for the photosynthetic reaction to take place. More water and nutrients will also be required, and a machete may be necessary to control the added, sometimes startling extra growth rates possible on most plants by using CO2 enrichment!
Eco Enterprises sells the following CO2 enrichment equipment:
- Bottled (compressed gas) CO controller system, comes with regulator and flow meter, timer, solenoid valve, tubing, balloon fittings and instructions. Price - $199.50
- CO2 fermentation kit, comes with nutrient, yeast, tubing, valve and instructions. Price - $17.50
2821 N.E. 55th St.
Seattle, Wa. 98105
(In WA 206-523-9300)